Right here, You can get information about How To Reset IP Camera Without Reset Button easily. It’s disheartening to discover that your IP camera doesn’t even have a reset button, especially if something goes wrong, and you need to reset it.

There are ways you can reset the device despite not having a button, so that it can once again work in the way it was supposed to. As mentioned, the resetting process will vary from one IP camera brand to the next.

How can I Reset my IP Camera Without Reset Button

It’s disheartening to discover that my IP camera doesn’t even have a reset button, especially if something goes wrong, and I need to reset it.

There are ways I can reset the device despite not having a button, so that it can once again work in the way it was supposed to. As mentioned, the resetting process will vary from one IP camera brand to the next.

For some IP cameras, I’ll have to use other buttons on the device to reset it.

• For example, if I have an Avigilon IP camera, I will have to disconnect the device from the power source and then press and hold down the firmware revert button. While doing this, I want to reconnect the power, and finally release the button after a few seconds.

• On the other hand, if I own an Axis IP camera, I’ll have to start by cutting the power to the device. Then, press and hold down the control button while I turn the power back on.

• I want to hold the control button for about 30 seconds so that the device’s orange lights come on. Then release the control button. I’ll know the process has been completed successfully when the device lights turn green.

• Some IP cameras only require to press and hold down the power button. An example are Canary IP cameras.

• All need to do is hold down the power button for about 12 seconds when the power is off, and wait for it to reboot before releasing the power button.

Related Questions about Reset IP Camera

1. What If I Can’t Reset my IP Camera?

There’s the possibility that my IP camera does not have a reset button, or any other way to reset it. This means if it isn’t working as it used to, I could not be able to reinstate its factory settings.

An example of an IP camera brand that can’t be reset is Mobotix. These cameras have been designed specifically so that they can’t be reset. This is meant to force return them to the manufacturer, if I encounter problems with them!

2. The IP Camera Reset Button Might Just Be Hidden

I have closely examined the exterior of my IP camera and come to the conclusion that it doesn’t have a reset button.

Sometimes, the button is actually hidden on the inside of the device. If this is the case, I will have to open the camera up to reset it.

• Unscrew the screws on the outside of the camera, so I can remove its cover or housing.
• I have also to remove screws that are on the device flap, so I can remove it.
• Once I’ve done that, I should see a main board. This is where I’ll find the reset button.
• I’ll see a black button. This is the one I need to press and hold it down for 30 seconds while the device has power.
• If the device has two copper holes instead of a black switch, I’ll have to short out the pads with an item like a paperclip. Do this for 30 seconds while the camera is on. This is similar to the way I’d reset an internet modem.
• If the device doesn’t have copper holes, but silver pins, I’ll have to short these out, in the same way as described above.

3. Can I Automatically Reboot my IP Camera?

If I don’t want the hassle of trying to figure out how to reboot and reset my IP camera, there is a way to automate the process and take the stress off my mind.

An example of a product that is WebRelay. It monitors any IP camera and DVR or NVR system and when it detects a problem, it will automatically reboot the device.

To set it up, all I have to do is connect WebRelay to my IP camera power and switch it on. Also make sure it’s connected to the same network that my IP camera is using. Then, enter WebRelay’s IP address, so I can use its setup and control settings.

Here, I’ll want to choose its network and automatic reboot settings. Once it’s been set up, WebRelay will take over by pinging the IP address of my camera. If it experiences ping failures, it will reboot the camera.

4. How does an IP camera work?

This camera can be used with a wired network, or wirelessly with the use of a Wi-Fi router.

5. Are IP cameras reliable?

The best wireless cameras are reliable, but they do depend on your network connection to be strong, in order to perform at their best.

Conclusion

As with any device, sometimes I need to reset or reboot my IP camera. But this isn’t always a straightforward process.

Some IP cameras do not have reset buttons. And some have hidden reset buttons.

I have need to open the camera up to get at the button on some models. With others, there is nothing can do at all. If it stops working, I have to send it back to the manufacturer.

Hopefully, I do not have one of these models. Even does not have a reset button, the vast majority of IP cameras can be reset in some other way.

I was included the more common ways in this article. If none work for your model, try to search for the manual on Google, or contact the manufacturer directly.