In this post, you can easily know about How To Login Netgear Orbi Router. To access the router login page, it is important that you are connected to the router.

You can find this information in the Manual of your Netgear Orbi router. If you don’t have the manual at hand or don’t want to search the complete manual for the login credentials, you can use the Quick install guide, which you can find below.

Login Guide for Netgear Orbi

• Open your preferred browser and enter 192.168.1.1 in the address bar to access admin panel of your router.

• Then you will see 2 fields where you can enter the router username and password.

• According to our database, the default username of your Netgear Orbi router is admin and the corresponding password is password.

• Enter the username and password, click on the login button, and now you should have access to the user interface of the router.

If the credentials do not work, try the following method

In the list below, you can find some of the most commonly used username/password combinations of Netgear routers. Try the following combinations. If you have problems logging in to the router, or you have forgotten your password.

• Admin – password
• admin – 1234
• admin – admin
• Comcast – 1234
• admin – (blank)
• admin – (specified by the user)
• (blank) – 1234
• admin – change me
• MSO/admin – change me/password
• admin – netgear1
• n/a – n/a
• super – 5777364
• cusadmin – (blank)
• admin – (specified by user)
• superman – 21241036
• n/a – password
• attadmin – (blank)
• (blank) – printed on router
• voo – WPA key on the label, uppercase
• admin – setup
• cusadmin – high speed
• (blank) – (blank)
• superuser – password

Hard reset instructions for Netgear Orbi Router (RBR50)

If your Orbi Router (RBR50) router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you’ve forgotten the password or misconfigured it and can’t get access anymore.

You can reset your Netgear Orbi Router (RBR50) in the following way(s):

With the reset button

• Have the router powered on (if just booted, wait around one minute for it to load)

• With a sharp pen or paper clip, press down the Restore Factory Settings button and hold it for about 7 seconds

• When the power light starts to blink, you can release the reset button and wait for the router to start up

• The power light will be solid (not blinking) once the router is started.

The 30-30-30 reset

• If the above instructions don’t work, you can always try the 30-30-30 reset as follows:

• When the router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)

• While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds

• While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.This process usually works for resetting any router to its factory setting.

How to log in to the Orbi Router (RBR50)

To log in to the Orbi High-Performance AC3000 Tri-Band Wi-Fi Router and change the settings, you can follow these steps:

• Make sure you are connected to the router’s network, either by Wi-Fi or Ethernet cable.

• Open your browser and visit http://192.168.1.1

• You should be prompted with a login dialogue.

• Enter the username: admin and the password: password

• Note: If you have already changed the password, use that instead.

• You will now be logged in. If you haven’t yet changed the default password, we recommend that you change it the first thing you do after logging in.

If these instructions don’t work for your router, you can always try a factory reset to get the default, or try some other common Netgear credentials, as they can usually be shared across models/variants.