Here you can get information about How to Reset Linksys Velop. Resetting the velop system as well as configuring it is kind of troublesome. So you have to perform the setup process again. All settings you have customized in setup and since things such as Wi-Fi name, passwords, security type will be erased.

All the wireless devices will be disconnected from your Wi-Fi, once you Reset Linksys Velop system.

So Here’s Your Guide to Reset Linksys Velop system:

• Primarily, press and hold the Reset button on the bottom of the velop system With the node turned on and connected to power.
• Now the light will turn red and fade by blinking on the top of the node.
• Wait till the light turns off and then turns into a bright red. Once the light turns into a bright red, release the button.
• The red light indicates that the process for Reset Linksys velop system is successful.

Tip: In case you have more than one node in your Velop system, you may need to reset them all to factory default settings. You can do that by resetting the main node; all other nodes will reset automatically.

Above were the steps to Reset Linksys velop system. Let us also discuss the steps to set up Linksys velop system in case you need it.

Firstly, in order to increase the connectivity and speed of your Velop system, you will be required to connect Linksys velop nodes with the Ethernet cables. Using a Linksys app, use a wireless connection in order to set up the additional Linksys velop nodes. Once the Node is Set up, connect the Linksys Velop nodes using Ethernet cables.

Follow the Below Steps to Set up Linksys Velop System.

• Now, through the Linksys app, set up the primary node.
• Again through the Linksys app, add a secondary node using the wireless setup.
• After the setup is completed, place the secondary node in the location where you want to move it and then connect it to a power outlet.
• Next, by using an Ethernet cable connect the secondary node to the primary node. The nodes will itself switch to an Ethernet wired connection.
• Lastly, use the Linksys app to add the other nodes as well. 
• After the setup is done, use an Ethernet cable to connect them.
• You are done setting up your Linksys velop system.

Linksys Velop system mesh WiFi is an interconnected series of nodes that ensures complete signal coverage to all or {any|to any or all} your devices. With Intelligent Mesh™ Technology, it goes a step ahead that focuses on the local area network signal strength supporting your current location at your home. Linksys velop system offers you a full strength signal all around your home. 

It allows you to connect all your smart, home automation, appliances, and voice controlled devices including Alexa. It provides you the Linksys app, from which you can control all your devices as well as Wifi anytime, anywhere.

The features are easy to access and include security control which allows you to keep your network protected and secure, automatic updates, and guest access as well which will provide your guests their own username and password so that they don’t have any difficulty to dig for password again and again.

Resetting your node

Resetting your Velop reverts it back to the state when you first took it out of the box.  This means that by resetting your node, all the settings that you have customized such as the Wi-Fi name, passwords, and security type will be erased and would need to be configured again.

Note: Before resetting the node, make sure that the node completely boots up showing a purple light or blue light (if the node has been previously set up).  Attempting to factory reset the node immediately after power cycling will not work so you must wait for a purple or blue light to show up before factory resetting the node.

Step 1:

• Make sure that your parent node is connected to a power source and turned ON.

IMPORTANT:  A parent node refers to the node that is physically connected to your modem.  All other nodes in your Velop system are considered child nodes.

Step 2:

• Press and hold the reset button at the bottom of the device.  The light on top of the parent node will turn red and fade in three pulses.  Do not release the button until the light goes out and then turns bright red.

After you reset and reconfigure the parent node, all child nodes will no longer be part of your Velop network.  

Step 3:

• Once you’re done resetting the parent node, perform the same steps above on each child node. 

Step 4:

• When you’ve successfully reset all your nodes, you should now be ready to set up your parent node and child nodes again. 

Step 5:

• After you’re done setting up all your nodes, check if everything has been added to your Velop network by going to Network Administration.  To access this page from the dashboard, tap the menu icon then tap Network Administration.  

With that, the process of Linksys Velop node reset is complete and now, you can enjoy fast and seamless internet in that part of the house where that non-functional node was present because it will now work smoothly.